TGL2205-SM 2-6 ghz 100 watt vpin limiter datasheet: rev - 05-08-14 - 1 of 10 - disclaimer: subject to change without notice ? 2014 triquint www.triquint.com 4 mm x 4 mm qfn package pad configuration pad number symbol 3 rf input 16 rf output 1,2,4,6,7,12,13,15,17- 19,24,25 gnd 5,8-11,14,20-23 no connection note: the rf input and output ports are not interchangeable. applications ? receive chain protection ? commercial and military radar general description the triquint TGL2205-SM is a high power, wideband gaas vpin limiter capable of protecting sensitive receive channel components against high power incid ent signals. the TGL2205-SM does not require dc bias and achieves a low insertion loss a ll in a small form factor. these features allow for simple integration with minimal impact to system performance. the TGL2205-SM operates from 2 to 6 ghz with low insertion loss of less than 0.6 db. it can limit up to 100 w incident pulsed-power with a low flat leakage of le ss than 16.5 dbm. the TGL2205-SM die has a protective surface passivation layer that provides enhanced environmental robustness. it is well suited for both commercial and defense related applications. lead-free and rohs compliant. product features ? frequency range: 2 to 6 ghz ? insertion loss: < 0.6 db ? peak power handling: 100 w (pulsed) ? flat leakage: < 16.5 dbm ? passive (no dc bias required) ? integrated dc block on output ? spike leakage < 0.5 db ? recovery time < 115 ns ? package dimensions: 4.0 mm x 4.0 mm x 1.47 mm functional block diagram ordering information part eccn description TGL2205-SM ear99 s and c-band 100w vpin limiter
TGL2205-SM 2-6 ghz 100 watt vpin limiter datasheet: rev - 05-08-14 - 2 of 10 - disclaimer: subject to change without notice ? 2014 triquint www.triquint.com absolute maximum ratings parameter value incident power, cw or pulsed, 50 , 25 c 100w incident power, cw or pulsed, 50 , 85 c 50w mounting temperature (30 seconds) 320 c storage temperature -40 to 150 c operation of this device outside the parameter rang es given above may cause permanent damage. these are stress ratings only, and functional operation of th e device at these conditions is not implied. recommended operating conditions parameter value passive ? no bias electrical specifications are measured at specified test conditions. specifications are not guaranteed over all operating conditions. electrical specifications test conditions unless otherwise noted: 25 c, tun ed evb results parameter min typical max units operational frequency range 2 6 ghz insertion loss < 0.6 db input return loss 12 db output return loss 12 db flat leakage power at p in > 30 dbm < 16.5 dbm pulse recovery time < 115 ns spike leakage < 0.5 db insertion loss temperature coefficient 0.003 db/c thermal and reliability information parameter test conditions value units incident power (rf operational life test 168 hours (1) ) frequency = 4.5 ghz, cw, 50 , 25 c 31 w frequency = 4.5 ghz, pulsed, pw=10us, dc=10%, 50 , 25 c 100 w notes: 1. test was terminated at 168 hours. insertion los s remained 1 db for device under test.
TGL2205-SM 2-6 ghz 100 watt vpin limiter datasheet: rev - 05-08-14 - 3 of 10 - disclaimer: subject to change without notice ? 2014 triquint www.triquint.com typical performance ? tuned evb performance test conditions unless otherwise noted: 25 c -1.6 -1.4 -1.2 -1.0 -0.8 -0.6 -0.4 -0.2 0.0 0 1 2 3 4 5 6 7 8 s21 (db) frequency (ghz) gain vs. frequency vs. temp. - 40 c +25 c +85 c 0 2 4 6 8 10 12 14 16 18 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 output power (dbm) input power (dbm) output power vs. input power vs. freq. 2.0 ghz 3.0 ghz 4.0 ghz 5.0 ghz 6.0 ghz temp. = 25 c -30 -25 -20 -15 -10 -5 0 0 1 2 3 4 5 6 7 8 s11 (db) frequency (ghz) input return loss vs. freq. vs. temp. - 40 c +25 c +85 c 0 2 4 6 8 10 12 14 16 18 0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 output power (dbm) input power (dbm) output power vs. input power vs. temp. frequency = 3.5 ghz - 40 c +25 c +85 c -30 -25 -20 -15 -10 -5 0 0 1 2 3 4 5 6 7 8 s22 (db) frequency (ghz) output return loss vs. freq. vs. temp. - 40 c +25 c +85 c 12 13 14 15 16 17 18 30 32 34 36 38 40 42 44 46 output power (dbm) input power (dbm) output power vs. input power vs. temp. frequency = 3.5 ghz - 40 c +25 c +85 c
TGL2205-SM 2-6 ghz 100 watt vpin limiter datasheet: rev - 05-08-14 - 4 of 10 - disclaimer: subject to change without notice ? 2014 triquint www.triquint.com typical performance ? tuned evb performance test conditions unless otherwise noted: 25 c 12 13 14 15 16 17 18 30 32 34 36 38 40 42 44 46 48 50 52 output power (dbm) input power (dbm) output power vs. input power vs. freq. 2.1 ghz 2.5 ghz 3.0 ghz 3.5 ghz 3.7 ghz temp. = 25 c cw input power 12 13 14 15 16 17 18 30 32 34 36 38 40 42 44 46 48 50 52 output power (dbm) input power (dbm) output power vs. input power vs. freq. 2.1 ghz 2.5 ghz 3.0 ghz 3.5 ghz 3.7 ghz temp. = 25 c pulsed input power = 10 usec/10% -30 -25 -20 -15 -10 -5 0 -6.0 -5.0 -4.0 -3.0 -2.0 -1.0 0.0 0 1 2 3 4 5 6 7 8 s11. s22 (db) s21 (db) frequency (ghz) s-parameters vs. freq., untuned evb s21 s11 s22 -30 -25 -20 -15 -10 -5 0 -6.0 -5.0 -4.0 -3.0 -2.0 -1.0 0.0 0 1 2 3 4 5 6 7 8 s11. s22 (db) s21 (db) frequency (ghz) s-parameters vs. freq., tuned evb s21 s11 s22
TGL2205-SM 2-6 ghz 100 watt vpin limiter datasheet: rev - 05-08-14 - 5 of 10 - disclaimer: subject to change without notice ? 2014 triquint www.triquint.com note: the rf input and output ports are not interch angeable. pad description bottom view package pad symbol description 1,2,4,6,7,12,13,15 ,17-19,24,25 gnd on pcb, multiple vias should be employed under 25 ( center pad) to minimize inductance and thermal resistance; see pag e 9 for suggested mounting configuration. 3 rf input input, matched to 50 ohms, not dc blocked 16 rf output output, matched to 50 ohms, dc blocked 5,8-11,14,20-23 nc no connection
TGL2205-SM 2-6 ghz 100 watt vpin limiter datasheet: rev - 05-08-14 - 6 of 10 - disclaimer: subject to change without notice ? 2014 triquint www.triquint.com applications information pc board layout rf layer is 0.020? thick rogers ro6020, r= 2.94. metal layers are 1-oz copper. microstrip 50 line width is 0.050?. the microstrip line taper at the connector interface is optimized for the southwest microwave end-launch connector 1092-02a-5. the pad pattern shown has been developed and tested for optimized assembly at triquint semiconductor. the pcb land pattern has been developed to accommodate lead and package tolerances. since surface mount processes vary from company to company, careful process development is recommended.
TGL2205-SM 2-6 ghz 100 watt vpin limiter datasheet: rev - 05-08-14 - 7 of 10 - disclaimer: subject to change without notice ? 2014 triquint www.triquint.com mechanical information package information and dimensions (units: millimet ers) the TGL2205-SM will be marked with the ?yyyy ? designator and a lot code marked below the part d esignator. the ?yy? represents the last two digits of the year the part was manufactured, the ?ww? is the work week, and t he ?xxxx? is an auto-generated number. this package is lead-free/rohs-compliant. the packa ge base is aluminum nitride and the plating materia l on the leads is gold over nickel (au-ni). this package is compatible with both lead free and tin-lead solderi ng processes. the lid is plastic.
TGL2205-SM 2-6 ghz 100 watt vpin limiter datasheet: rev - 05-08-14 - 8 of 10 - disclaimer: subject to change without notice ? 2014 triquint www.triquint.com mechanical information (continued) mounting configuration notes: 1. ground / thermal vias under the dut are critical for the proper performance of this device. 2. the evb shown herein utilizes copper filled vias (8 mil diameter) under the dut to maximize heat tr ansfer away from the dut under large signal conditions. 3. thermal dissipation is low for normal non-limiti ng operation.
TGL2205-SM 2-6 ghz 100 watt vpin limiter datasheet: rev - 05-08-14 - 9 of 10 - disclaimer: subject to change without notice ? 2014 triquint www.triquint.com product compliance information esd sensitivity ratings caution! esd-sensitive device esd rating: tbd value: tbd test: human body model (hbm) standard: jedec standard jesd22-a114 solderability compatible with the latest version of j-std-020 lea d free solder, 260 c. this part is compliant with eu 2002/95/ec rohs directive (restrictions on the use of certain hazar dous substances in electrical and electronic equipment). this product also has the following attributes: ? lead free ? halogen free (chlorine, bromine) ? antimony free ? tbbp-a (c 15 h 12 br 4 0 2 ) free ? pfos free ? svhc free msl rating tbd at 260 c convection reflow the part is rated moisture sensitivity level tbd jedec standard ipc/jedec j-std-020.
TGL2205-SM 2-6 ghz 100 watt vpin limiter datasheet: rev - 05-08-14 - 10 of 10 - disclaimer: subject to change without notice ? 2014 triquint www.triquint.com contact information for the latest specifications, additional product i nformation, worldwide sales and distribution locati ons, and information about triquint: web: www.triquint.com tel: +1.972.994.8465 email: info-sales@triquint.com fax: +1.972.994.8504 for technical questions and application information : email: info-products@triquint.com important notice the information contained herein is believed to be reliable. triquint makes no warranties regarding the informat ion contained herein. triquint assumes no responsibility or liability wha tsoever for any of the information contained herein. triquint assumes no responsibility or liab ility whatsoever for the use of the information con tained herein. the information contained herein is provid ed "as is, where is" and with all faults, and the e ntire risk associated with such information is entirely with the user. all information contained herein is subject to chan ge without notice. customers should obtain and verify the latest relev ant informa tion before placing orders for triquint products. the information contained herein or any use of such inf ormation does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether with r egard to such information itself or anything described by such information. triquint products are not warranted or authorized f or use as critical components in medical, life-savi ng, or life- sustaining applications, or other applications wher e a failure w ould reasonably be expected to cause severe persona l injury or death.
|
